Toilet & Faucet Repair and Installation Services
Fix running toilets, leaking faucets, low water pressure, and install new fixtures. Same-day service.
About Toilet & Faucet Repair
Toilets and faucets are the most frequently used plumbing fixtures in your home, and small problems with them quickly become big annoyances — and expenses. A running toilet can waste 200 gallons of water per day, adding $50–$200 per month to your water bill without you noticing. A dripping faucet that wastes one drop per second loses 3,000 gallons of water per year. These aren't just nuisances — they're costly water waste that professional repair can eliminate quickly and affordably.
Common toilet repairs include replacing the flapper (the rubber seal that controls flush valve seating), adjusting or replacing the fill valve, repairing or replacing the flush handle and chain, fixing toilet rocking by replacing the wax ring, unclogging slow or non-flushing toilets, and addressing running water noise. Most toilet repairs cost $75–$175 for parts and labor and can be completed in under an hour. Full toilet replacement runs $300–$600 installed, and upgrading to a WaterSense toilet saves 10,000–20,000 gallons of water annually.
Faucet repair and replacement covers leaking handles, dripping spouts, low water pressure from aerator buildup, difficulty turning handles (worn cartridges), and completely replacing outdated or damaged fixtures. Faucet repair typically costs $75–$150 for basic repairs. Full faucet replacement with a homeowner-supplied fixture runs $100–$250 labor; with plumber-supplied premium fixtures, $200–$600 total. Kitchen faucets, bathroom vanity faucets, shower/tub valves, and outdoor hose bibs each have distinct repair approaches.
Low water pressure at specific fixtures is often caused by clogged aerators (the mesh screen at the faucet tip) or a clogged showerhead — easily cleaned or replaced for $5–$30 DIY. Pressure low throughout the home indicates pressure regulator failure, partially closed shutoff valves, or pipe-scale buildup requiring professional diagnosis.
Toilet & Faucet Repair Cost Guide — 2026 National Averages
Costs vary by location, access, and job complexity. Use these as starting benchmarks.
| Service Item | Typical Range | Low End | High End |
|---|---|---|---|
| Toilet flapper replacement | $75–$150 | $50 | $200 |
| Fill valve replacement | $100–$200 | $75 | $300 |
| Toilet installation (labor) | $150–$300 | $100 | $450 |
| Faucet cartridge replacement | $100–$200 | $75 | $300 |
| Faucet installation (labor) | $100–$250 | $75 | $400 |
| Wax ring/toilet re-set | $100–$200 | $75 | $350 |
| Hose bib replacement | $125–$250 | $75 | $400 |
* Prices based on national averages. Rates in major metro areas (New York, San Francisco, Los Angeles) typically run 30–80% higher. Rural areas may be 10–20% lower.
Signs You Need Professional Toilet & Faucet Repair
The most common cause is a worn or misaligned flapper that doesn't fully seal the flush valve. A toilet that runs continuously can waste 200+ gallons per day — add food coloring to the tank to confirm if water is leaking into the bowl.
A failing fill valve or float that doesn't shut off water at the proper level. Left unaddressed, it can overflow the bowl or tank.
Worn cartridges, O-rings, or washers allow water to bypass the valve seal. Even a slow drip wastes thousands of gallons annually and should be repaired promptly.
Worn cartridges inside the valve body make handles hard to turn or prevent precise temperature control. Replacement cartridges are often $20–$60 and resolve the issue completely.
Check the aerator first (unscrew and clean it). Persistent low pressure at a single fixture may indicate a partially closed shutoff valve under the sink or a supply line restriction.
A loose toilet typically needs a new wax ring seal and tightening of the floor bolts. Ignoring this allows sewer gas to leak into the bathroom and can damage the floor around the base.
What to Expect from Your Toilet & Faucet Repair Service
Plumber diagnoses the specific problem (10–15 minutes)
Parts identified — most common parts are stocked on the service truck
Written estimate before work begins
Repair completed: most toilet and faucet repairs take 30–90 minutes
Full test: flush multiple times, run water to check for drips or running
Water bill savings explained — plumber may note estimated waste reduction
DIY vs. Professional Toilet & Faucet Repair
| Approach | When It Works | When to Call a Pro |
|---|---|---|
| Replacing toilet flapper | ✓ Easy DIY — $5–$15 part at any hardware store | ✗ Turn off water, flush, unhook old flapper, snap on new one. 10-minute fix. |
| Unclogging toilet | ✓ DIY with a plunger or closet auger | ✗ Use a flange plunger; if repeated plunging fails, call a plumber |
| Replacing faucet aerator | ✓ Easy DIY — $3–$8 at hardware store | ✗ Unscrew aerator, clean or replace, reinstall. Fixes low flow pressure immediately. |
| Replacing faucet cartridge | ✓ DIY for handy homeowners | ✗ Requires matching cartridge brand/model; lever faucets are easier than two-handle |
| Replacing toilet or faucet entirely | ✓ DIY possible but time-consuming | ✗ Requires supply line shutoff, connections, potential caulking; mistakes cause leaks. Pro takes 30–60 min. |
Find a Toilet & Faucet Repair Pro Through Our Partners
Compare quotes from top-rated local plumbers on the platforms homeowners trust most.
Get a Free Toilet & Faucet Repair Quote
Fill out the form — a licensed plumber will call you within 15 minutes.